Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
This great article which follows involving A Step-by-Step Guide to Installing a Bathtub is pretty much interesting. Don't skip it.
Installing a bath tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is also a moderately hard task. If the old tub is readily available, the project can move immediately; if you have to open up a wall surface to remove the old tub and place the new tub, the job is a lot harder. In either instance, the job is within a home handyman's skills, although you will need a helper to leave the old tub as well as embeded in the new one. Make sure you have actually qualified yourself for the job as well as are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to consider using one before you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bath tub in your restroom if you have actually currently gotten a brand-new tub as well as do not need to change the plan of your previous water pipes.
Your tools and material list should consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome due to the restricted accessibility that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines remain in location between the faucet as well as the sink. Protect the faucet in position with the manufacturer given backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap adapters. The former type must be attached to the tap ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using the two wood boards under its feet, place the bath tub in the called for position. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and also check all joints and brand-new pipework for leakages and tighten them if necessary. Load the bath tub and likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait until the tub has been used at the very least once as this will certainly resolve it into its final position.
Getting ready for the Installation
To start with, the supporting frame provided with the bath needs to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can crack relatively early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking time to read through our short article. Enjoyed reading our review? Please share it. Let another person discover it. Thanks for taking the time to read it.
Address leaks promptly. Report this page